1. Welcome to TRD Forums! A community for Toyota, Lexus, and Scion Enthusiasts. To enjoy all the benefits of the site, we invite you to signup.

Forced Induction Help! Split Second ESC-1 on 2001 Corolla

Discussion in 'Powertrain' started by Barnacules, 2009年10月29日.

  1. Offline

    Barnacules 100101101011011

    Message Count:
    2,933
    ライク受信:
    1
    賞:
    0
    Location:
    Duvall, WA
    Help! Split Second ESC-1 on 2001 Corolla

    Does anyone have any idea or any instructions on how to hook a SplitSecond ESC-1 up to a 2001 Toyota Corolla? I'm thinking about pulling the Turbo Rolla out of mothballs and try to get it back on the street again but without the ESC-1 it will just run super lean under boost and pop another engine. Any help would be appriciated since I am going to attempt the install and put the car back togather tomorrow.

    Thanks!
    Barnacules, 2009年10月29日
    #1
  2. Offline

    Barnacules 100101101011011

    Message Count:
    2,933
    ライク受信:
    1
    賞:
    0
    Location:
    Duvall, WA
    Wow, nobody? C'mon :D Vamp, were are you! :D
    Barnacules, 2010年08月04日
    #2
  3. Offline

    SaberJ2X Lurk MOAR

    Message Count:
    1,713
    ライク受信:
    7
    賞:
    398
    Location:
    Mayawest, PR
    he went a away a pretty looooong time ago xD
    SaberJ2X, 2010年08月04日
    #3
  4. Offline

    DeebsTundra Big Tires :)

    Message Count:
    2,797
    ライク受信:
    10
    賞:
    318
    Location:
    Near VoRtEx
    Vamp's been gone for YEARS man. He was pretty much gone when I joined in '05.
    DeebsTundra, 2010年08月04日
    #4
  5. Offline

    vortex Well-Known Member

    Administrator
    Message Count:
    4,110
    ライク受信:
    48
    賞:
    748
    Location:
    Westminster, CO
    the ESC1 goes between the the O2 sensor and the ECU on the signal wire. it's meant to manipulate the signal coming from the O2 sensor to the ECU while under boost to trick the ECU into thinking that the mixture is stoimetric so that the ECU doesn't cut fuel when it senses that you're running rich (which you do under boost). If you don't know which wire this is, measure with a meter. Don't put it on the constant signal wire, put it on the fluctuating.

    The question of the hour is... you bought the ESC-1 knowing what it should do but don't know how to install it? I fear for you. ;)
    vortex, 2010年08月06日
    #5
  6. Offline

    Barnacules 100101101011011

    Message Count:
    2,933
    ライク受信:
    1
    賞:
    0
    Location:
    Duvall, WA
    No worries, I knew what it did I just wanted some help with the pinouts on the ECU, etc. But we got it figured out 2 days ago and it is installed and functioning and the car is holding 11-12AFR under bost. we'll fine tune it later on I just wanted it drivable without burning up the rings :D
    Barnacules, 2010年08月06日
    #6

TRDの愛を広める